Field Fence Knot Types: Hinge Joint vs Fixed Knot
Field fence knot types decide how a woven panel behaves the first time an animal leans on it. Two constructions dominate export orders: the hinge joint, where each stay wire is crimped around the line wires in a loop that can still slide, and the fixed knot, where the stay wire is wrapped and locked so nothing moves. Both are sold as field fence and both are galvanised, yet they are not interchangeable in the paddock: one absorbs impact and recovers, the other holds its shape against an animal that keeps working the same spot. This guide compares how each is built and which one to specify.
What the Knot Actually Does
A panel is a grid: line wires carry tension, stay wires hold the line wires at height, and the junctions keep the grid together. The knot is the only element transferring pull from one wire into the other, and the point where every impact concentrates.
Load Path From Line Wire to Stay
When an animal presses on a panel, the nearest line wires bend inwards and pull the stays sideways. At each junction the load passes from the deflected line wire into the stay. A junction that can slide spreads the load along the wire; one that cannot slide takes the whole local force itself, which explains most of the behaviour below.
Why the Junction Fails First
Crimping and wrapping both scratch the zinc at the spot where water sits longest, because a knot forms a small crevice. A panel usually rusts at a junction before it fails mid-wire, which is why coating quality at the knot matters as much as gauge.
Hinge Joint: A Crimped Loop That Can Slide
The hinge joint is the older, cheaper construction. Each stay is bent into a closed loop at every line wire and closed by crimping, leaving slack to hinge. The panel behaves like a net rather than a rigid sheet: it deforms under a push and springs back.
Where Hinge Joint Wins
It suits cattle and boundary grazing where an animal tests the fence once and moves on. The mesh gives under a shoulder and returns to shape, where a rigid panel would take the full load at one junction. A flexible panel also follows undulating ground, which is why long rolls on large blocks are usually hinge joint.
Fixed Knot: Wire Locked Around the Stay
The fixed knot reverses the priority. The stay wire itself wraps around the line wire and is knotted back on itself, so the junction is a locked mechanical joint rather than a crimped hinge. The panel reads as a stiff grid that keeps its shape under pressure.
Where Fixed Knot Wins
Specify it where animals work the fence continuously: goats and boars that rub and lift, rams testing with their heads, sheep under predator pressure, and boundaries beside a road or neighbour. Nothing slides, so the mesh cannot be pushed into a shape that leaves a gap at the bottom, and the grid holds tension without creeping out of geometry. The wrap also consumes stay wire, so the roll is heavier and stiffer than hinge joint at the same gauge.
Side by Side: Wire, Weight and Stiffness
Weight shows the difference on paper. A 2.5 mm galvanised wire at 150 mm pitch both ways needs 13.1 m of wire per square metre of mesh, or 38.5 g per metre: 0.505 kg per square metre, about 0.61 kg of mesh wire per running metre of 1.2 m fence, and roughly 61 kg per 100 m roll before posts and packaging. With 2.0 mm wire the same geometry drops to 0.324 kg per square metre, 0.39 kg per running metre and about 39 kg per roll.
Now the knot. A 1.2 m panel with stays at 150 mm and eight line wires has roughly 53 junctions per running metre. If a locked knot takes about 30 mm of stay wire that would otherwise run straight, that is 1.6 m of extra wire per metre of fence, about 12 % more mesh wire than the hinge joint version of the same gauge. That is an estimate from wrap length, not a catalogue figure; ask for kilograms per roll if you need the exact comparison.
| Property | Hinge joint | Fixed knot |
|---|---|---|
| Junction | Crimped loop, slides a few mm | Wrapped and locked |
| Impact response | Deflects and recovers | Holds shape, local load |
| Mesh wire | Baseline | About 12 % more |
| Best animals | Cattle, boundary grazing | Goats, rams, predator pressure |
| Ground | Undulating, long rolls | Straight runs, exposed sites |
| Repair | Re-crimp locally | Replace the panel section |
Slopes, Sand and Frost Heave
On a grade, hinge joint follows the surface better and needs fewer corrective stakes, but it sags between posts as tension drops. Fixed knot holds shape on a slope and tolerates frost movement because the grid cannot creep, provided posts are set deep enough. Sandy ground is a post problem more than a wire problem: no knot survives a post that lifts.
What to Put on the Order
State height, line and stay gauge, zinc mass in g per square metre, roll length, and the knot type in words rather than a code. Add your post spacing: a 2.4 m panel needs about 42 posts per 100 m plus end assemblies, and a post that is too light will fail before either knot does. Confirm the zinc class at the knot matches the line wire, because a thin coating at the junctions will rust first where the load sits.
For the mesh, see our woven field fence and the full field fence range. Posts and fittings are listed separately, including the 1.5 lb galvanised T post used on most grazing blocks. Send height, gauge and animal to WhatsApp or phone +86 158 0311 4155, or email sales@cndutai.com, and we will quote from Anping City, Hengshui City, Hebei, China.
FAQ About Field Fence Knots
Q: Is fixed knot stronger than hinge joint?
Stiffer, not automatically stronger. Fixed knot resists distortion and repeated rubbing far better; hinge joint survives a single heavy impact by deflecting. For continuously worked fences, fixed knot is more durable.
Q: Can I mix the two knot types in one line?
Avoid it. A flexible panel next to a rigid one concentrates movement at the joint between them, and that is where the fence first distorts. Keep one knot type per continuous run.
Q: Does the knot type change post spacing?
Only slightly. Fixed knot holds tension longer, so it needs less maintenance at 2.4 m. On exposed sites or light soils, shorten spacing for either type rather than relying on the knot.
Q: Which knot suits electric fencing?
Neither is an electric fence. If electric wire runs above a woven panel, hinge joint is usually enough, because the live strand takes the animal pressure before the mesh does.
Q: How can I tell them apart on delivery?
Look at one junction. A hinge joint shows a closed crimped loop with visible slack where the stay can move; a fixed knot shows the stay wrapped around the line wire and knotted back on itself, with no free movement when you twist the grid.