Galvanized Fence Post Coating: Zinc Classes Explained
Galvanized fence post coating is the specification most often left off an order, and it is the one that decides how the post looks in ten years. Two posts can share the same section, the same length and the same weight per metre, and still behave differently on site because one carries a thin pre-galvanized skin and the other carries a hot dip coating with mass behind it. This guide explains what the coating number means, converts coating mass to thickness, compares hot dip with pre-galvanized strip, shows where a coating fails first, and sets out what to write on an enquiry so the post that arrives matches the duty.
What the Coating Number Means
Galvanized coating on a fence post is specified as mass per unit area, in grams per square metre, and quoted as the total on both surfaces. Because zinc weighs about 7.14 grams per cubic centimetre, coating mass converts to thickness at roughly 7.14 grams per square metre per micrometre. A 60 g/m2 coating is about 8.4 micrometres total, or 4.2 micrometres per side; 120 g/m2 is about 16.8 micrometres total; 275 g/m2, the familiar Z275 designation for coil, is about 38.5 micrometres total or 19.3 per side; 610 g/m2 reaches about 85 micrometres total. The per-side figure is the one that matters, because each face has to carry its own corrosion load.
Coating Mass Table
| Coating mass (g/m2, both sides) | Thickness total (micrometre) | Per side (micrometre) | Typical use |
|---|---|---|---|
| 60 | 8.4 | 4.2 | Indoor or dry shelter only |
| 120 | 16.8 | 8.4 | Short-life temporary lines |
| 180 | 25.2 | 12.6 | Light duty, dry inland sites |
| 275 | 38.5 | 19.3 | General stock fencing |
| 305 | 42.7 | 21.4 | Hot dip minimum, 1.5 to 3 mm steel |
| 610 | 85.4 | 42.7 | Coastal, high humidity, long life |
Hot Dip Against Pre-Galvanized
Pre-Galvanized Strip
A T post made from pre-galvanized coil is coated before it is formed. The surface is uniform and the cost is low, but every cut end, punched hole and weld seam is bare steel, and the coating is thin because it came from a coil line. On a post that is driven into the ground, the bare end sits exactly where moisture collects.
Hot Dip After Fabrication
Hot dip galvanizing happens after the post is cut, punched and welded, so zinc covers the ends and the seams as well as the flat. Coating mass is higher and the layer is metallurgically bonded rather than deposited. The trade is cost and a rougher finish, and for a post that will be driven into soil, it is usually the right trade.
Where a Coating Fails First
Three places account for most failures: the cut end at the top of a driven post, the weld seam where a stud or a plate meets the section, and the ground line where wet soil and air meet. A post with a good flat face and a bare cut end still rusts from the top down, and a post that is scratched during handling rusts at the scratch. Coating mass that is measured only on the flat misses the area that decides the outcome.
Ground Line and Backfill
The base of a driven post is the hardest environment on the fence: alternating wet and dry, with abrasion from the soil during driving. A coating of 19 micrometres per side is a thin barrier in that position, which is why a heavier coating or a sacrificial layer pays off on long-life lines. Where soil is acid or the water table is high, the case for extra coating mass is stronger than any argument about the flat surface.
Estimating Service Life
Published atmospheric corrosion rates for zinc run at roughly 0.5 to 1 micrometre per year in clean rural air, 2 to 4 in urban and industrial air, and 3 to 5 in coastal salt exposure. On that basis, 19 micrometres per side gives an order of twenty years inland and a handful of years on a coast; 43 micrometres per side moves both cases out by a factor of two. These are order-of-magnitude figures for planning, not a warranty, because soil chemistry and abrasion change the answer.
Repairing a Damaged Coating
Any scratch, cut end or weld that is bare should be treated before the post goes into the ground. A zinc-rich cold galvanizing compound applied to a clean surface restores a sacrificial layer; paint alone protects by barrier and fails once moisture reaches the edge. On site, the practical rule is to repair the ends when the bundle is opened rather than after the line is up.
Storing and Handling
Keep bundles off the ground and under cover, and avoid dragging posts across each other. Most handling damage happens in the first ten minutes after a delivery, when bundles are dropped and dragged to the line. A post that arrives with a good coating and is installed carefully keeps it; a post that is dragged over gravel loses coating at the ends before it is driven.
Specifying on the Order
Write coating mass in grams per square metre, state whether it is total or per side, name the standard you want the coating tested against, and say whether the post is hot dip galvanized after fabrication. Add the destination port and the site condition, so the supplier can propose the class that suits the exposure rather than the cheapest one on the list. See the 1.5 lb hot dip galvanized T post, the 2.04 kg/m galvanized T post, and the full T post range.
FAQ About Galvanized Fence Post Coating
Q: What coating mass should a fence post have?
275 g/m2 is a common general-purpose class; 305 g/m2 and above is typical of hot dip after fabrication, and coastal sites justify 610 g/m2.
Q: How do I convert g/m2 to micrometres?
Divide coating mass by about 7.14 grams per square metre per micrometre, then halve the result for a per-side figure.
Q: Is pre-galvanized strip good enough?
For dry, sheltered and short-life use yes; for posts driven into soil the bare cut ends and thin coating are the weak points.
Q: Can a scratched post be used?
Yes, if the bare area is treated with a zinc-rich cold galvanizing compound before it is installed.
Q: Can posts be supplied to a named coating class?
Yes. Send coating mass, standard, length, quantity and destination port to Dutai. WhatsApp / Mobile: +86 158 0311 4155 | Email: sales@cndutai.com or info@studdedtpost.com. Address: Anping City, Hengshui City, Hebei Province, China.